Gimp logo11/13/2023 ![]() ![]() These layers are used to create the edge lighting for the text. Step 5 ¶ĭuplicate the blurred layer once (tmp1 and tmp2). You will need to make sure that the layer boundary is larger than the layer so that the blur can spread nicely. When I did the original logo, it was set lower than this to make the effect less rounded. I used Gaussian Blur ( RLE) at 10 pixels. Step 4 ¶ĭuplicate the text layer again and move it to the top of the Layers stack (use the little up facing arrow head on the Layers, Channels, & Paths dialog). means “Keep Transparency” this will ensure that any transformations or fills made to that layer will only affect the non-transparent part of the image. You can do this easily by dragging the white color swatch from the toolbox over to the image (assuming that the highlight layer is currently selected). ![]() box on the Layers, Channels, & Paths dialog, and fill it with white. The highlight layer needs to be white, so select that layer, check the Keep Trans. One for the highlight effect (highlight) and one for the shaded part of the effect (lowlight). Step 3 ¶ĭuplicate the text layer (text) twice. Do so by accessing the Layers menu (right click or Control+Click on the layer you wish to operate on) and select Layer to Imagesize. It will help to change the layer size to that of the image. If you use GIMP FreeType then it is done for you, otherwise click the New Layer button in the Layers, Channels, & Paths dialog (looks like a blank piece of paper). The text should be created as a new layer. Start by laying down some text that is wider than 400px and not too thin. I feel this size it adequate as my website at the time of writing uses 500px tables. I used a white background at 500px by 200px. I’ve taken a lot of screen shots to support this tutorial, so enjoy :) Step 1 ¶įire up GIMP and create a new image. I’ll point out the differences as I go along. This is the same procedure I used to create the logo on my homepage, albeit with slightly different settings. The more experienced user may find some techniques here useful. This tutorial is aimed squarely at the novice GIMP user. If you have any questions, comments or concerns, drop them comments section below.Text and images Copyright (C) 2002 Mel Boyce and may not be used without permission of the author. If these steps were a bit too general for you to follow along with then I would recommend watching the video tutorial where I go over everything step-by-step with voice narration. You can use the white circle at the very bottom layer as a reference point for doing this.įinally, we’ll grab our Text tool and simply add some text on its own layer using the Mattilda font, and with that your logo is complete. Next, duplicate your tab layer, flip it vertically, then merge it with the original layer and delete the portion of the tabs that protrude past outside of the circle. After that you can turn the visibility of the other layers back on. Use the Paintbrush tool to add a white star on top of the black tab, then merge all of the visible layers and change the new layer’s size to fit the image. Now duplicate the tab, scale it up a little bit, fill it with white and lower beneath the gray tab layer. Use that newly rotated rectangle as a reference point to delete the bottom portion of the gray rectangle, leaving us with the following tab shape… Use the Rectangle tool to create a perfectly symmetrical white square on a new layer, rotate it 45 degrees, set the opacity of the layer to 50% and center it vertically towards the bottom of the gray rectangle, as depicted below. Autocrop the layer, then align it to the center of the canvas vertically. Now we’re going to add a couple of tabs on both the top and bottom, so turn off the visibility of all layers and create a new layer (that is visible) and create a rectangle selection at the top of the canvas, then fill it in with 1A1A1A. Again, we’ll create another layer and another slightly smaller circle, only instead of filling it with a color we’ll add a 25 pixel stroke in white. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |